服務熱線電話
400-6188-756
超聲波清洗機有哪幾種溫控方式?
來源:http://www.szoudao.com/ 時間: 2024-05-28 瀏覽次數: 0
1、數控面板加熱
1. CNC panel heating
一般實驗室使用的數控超聲波清洗機,帶加熱功能的機型,為數控按鈕加熱。數控區顯示當前溫度,可設置溫度值。當達到加熱值時,自動停止加熱。這種加熱一般用硅膠板加熱。
The CNC ultrasonic cleaning machine commonly used in laboratories, with a heating function model, is equipped with a CNC button for heating. The CNC area displays the current temperature, and the temperature value can be set. When the heating value is reached, the heating automatically stops. This type of heating is usually done using a silicone plate.
2、機械溫度控制
2. Mechanical temperature control
普通超聲波清洗機一般采用機械控溫,即旋鈕調節溫度。
Ordinary ultrasonic cleaning machines generally use mechanical temperature control, which means adjusting the temperature with a knob.
3、溫控器加熱
3. Temperature controller heating
分體式超聲波清洗機可根據使用情況通過溫控器進行加熱。
The split type ultrasonic cleaning machine can be heated through a temperature controller according to the usage situation.

使用方法如下:按下加熱開關,溫控器將顯示測量溫度和控制溫度。上方顯示的是測量溫度,下方顯示的是控制溫度。當被測溫度低于控制溫度時,溫控器上的out燈亮,加熱指示燈亮,設備處于加熱狀態;當被測溫度高于控制溫度時,溫度控制儀表上的out燈滅,加熱指示燈滅,設備停止加熱。
The usage method is as follows: Press the heating switch, and the temperature controller will display the measured temperature and the controlled temperature. The temperature measurement is displayed above, and the temperature control is displayed below. When the measured temperature is lower than the control temperature, the out light on the temperature controller lights up, the heating indicator light lights up, and the equipment is in a heating state; When the measured temperature is higher than the control temperature, the out light on the temperature control instrument goes out, the heating indicator light goes out, and the equipment stops heating.
控制溫度設置方法:按撥號鍵設置控制溫度,控制溫度為58度。這種類型一般采用加熱管加熱。
Temperature control setting method: Press the dial key to set the control temperature to 58 degrees. This type generally uses heating tubes for heating.
以上就是有關:超聲波清洗機 的介紹,想了解更多的內容請點擊:http://www.szoudao.com 我們將會全心全意為您提供滿分服務,歡迎您的來電!
The above is an introduction to ultrasonic cleaning machines. To learn more, please click: http://www.szoudao.com We will wholeheartedly provide you with full score service. Welcome to call us!
相關產品
相關文章
-
汽車零部件清洗效率低?全自動碳?xì)淝逑礄C(jī)太能打! 2025-12-20
-
通過式噴淋清洗機:影響在電子車間內流暢使用的5大影響因素 2025-12-20
-
金屬零件清洗怕踩坑?碳?xì)淝逑礄C(jī)夠硬核,難題全搞定! 2025-12-19
-
50Mpa CNC高壓清洗機:強力瓦解各類油污、碎屑,工業清潔高效之選 2025-12-19
-
多槽手動超聲波清洗機:選對工業清洗設備,效率直接拉滿! 2025-12-19
-
噴淋清洗機霧氣過大?水霧收集器這樣徹底解決! 2025-12-18
-
通過式噴淋清洗機:發動機缸體定制化清洗解決方案,自動化高效賦能車企 2025-12-18
-
多孔盲孔清洗難題?碳?xì)淝逑礄C(jī)憑真空技術精準破解 2025-12-18
-
CNC 高壓清洗機:50 兆帕精準沖洗,攻克油垢毛刺難題 2025-12-18
-
CNC高壓清洗機:三合一全能清洗,多行業適配的工業利器 2025-12-17

新聞中心




常見問題







魯公網安備37011202000628號